 |
|
|
Installation
instructions:
F-16CJ widescreen Superpit version 2.0,
April 2009 |
|
This version is intended for Falcon 4.0
with FF5. The native resolution is 1920x1200(16:10), autoscaling will
allow 1680x1050 and 1440x900. Running the cockpit in 16:9 is also possible
but will result in slight horizontal stretching in the 2D cockpit.
| |
F-16CJ pit installation |
| Step 1 |
Run
the F16CJwide_v2.0 installer.
|
| Step 2 |
Agree
with the EULA and select
install (reinstall completely or look for update if installed
earlier)
|
|
Wait
until the installer is completely finished and it confirms the add-on is
installed successfully
|
| Step 3 |
Start
Falcon and select an F-16CJ Falcon to fly in either Dogfight,
|
|
Tactical
Engagement or Campaign mode.
|
|
|
|
|
| |
Settings |
|
These
are recommended settings, with and without use of TrackIR:
|
| Step 1 |
Run
the FFViper Config Editor in your FreeFalcon5 dir
|
| Step 2 |
Point
it to your FreeFalcon5 FFViper.exe
|
| Step 3 |
Go
to ‘Cockpit settings’
|
| Step 4 |
3Dcockpit
FOV – Set to 60 (Default)
|
| Step 5 |
Click
Apply
|
|
|
|
|
|
|
| |
Tweaks |
|
If
you want to fly the F-16A or F-16 blk 30, you need to make use of the CJ's
3D cockpit data for correct positioning of the MFD's. Here are the
steps:
|
| Step 1 |
Back
up FreeFalcon5\art\ckptart\3Dckpit.dat
|
| Step 2 |
Copy
FreeFalcon5\art\ckptart\F-16CJ\3DCKPIT.DAT
|
| Step 3 |
Paste
and overwrite the file in FreeFalcon5\art\ckptart
|
|
|
|
|
|
| F/A-18C
Hornet Superpit features and tips:
features: |
2D cockpit:
|
| Graphics
- This install allows autoscaling, therefor it is possible to fly in lower resolutions
like 1680 x1050 or 1440x900. The default resolution is 1920x1200. |
|
| Photorealistic
- cockpit with as real as possible
functionality, within the limits of the Falcon simulator software. |
|
| Kneeboards
- The right kneeboard has 12 pages of browsable checklists for preflight and rampstart, ETR
(Enemy Treat Ranges), refueling checklist, Fence checklists.
|
|
Nightlighting
- On the Internal Lights panel at the right down side you can enable floodlight by selecting the FLOOD switch.
For enabling Instruments lights and backlit panels you hit keys Shift-2 and you turn the 'CONSOLES' knob to BRT.
|
|
| Extra functionality
panel - When keys Shift-1 are selected you will get a panel with extra large
HUD/MFD display data, fully clickable. |
|
| Rampstart
- A full rampstart is possible, complete checklists on the right
knee. |
|
| 3D
cockpit: |
| Functionality
- Fully clickable (although most switches will not move) and
gauges/instruments operational. |
|
| Canopy -
canopy movements when opening and closing. |
|
6DOF
- 6DOF TrackIR4 is recommended for full enjoyment.
If you don't have 6DOF enabled, open the 'FFViper config editor'
in the FreeFalcon5 directory, 'TrackIR settings', TrackIR DOF
support, then enable 'Yaw pitch Roll,X Y Z' and click 'Apply'.
|
- Trim on Stick
There is a imaginary cross on the stick's trim button, using this
cross and left and rightclick will let you trim the plane. |
|
| Credits for
this add-on: |
| -
Eric ‘Aeyes’ de Best
– 2D/3D Cockpit textures,
2D cockpit functionality, 3D cockpit model design, loading and leaving
‘splashscreens’, ejected pilot model and textures, manual, quality
checks
|
| -
Stefano ’Qawa’
–
3D cockpit adjustments
|
| -
Mike’Homercide’ Hom
- Installer
|
|
|
-
Special thanks to the FreeFalcon development team for creating this
basis for this Falcon add-on. |
|
-
Also special thanks to the Microprose,
Ibeta, RPG, eFalcon, F4UT, BMS and
RV
teams who made it possible to advance this Falcon 4.0 simulation over
the years.
|
|
|
|
